A disposal that hums without turning is usually jammed, not dead. One that leaks from its own body usually is done. Two very different visits.
A hum with no grinding usually means the motor has power and the turntable cannot move. Switch the disposal off first and keep your hand out of the chamber. Many units have a hex socket dead center on the underside, facing the floor. InSinkErator ships a small crank-shaped wrench for it and says a standard 1/4-inch Allen wrench also works. Its instructions: work the wrench back and forth in both directions until it turns freely in complete circles, then look into the chamber with a flashlight and lift anything out with tongs or pliers.
Then check the red overload button on the bottom of the unit. InSinkErator says a tripped button sits dropped about a quarter of an inch; press it gently, and if it does not stay up, wait ten minutes and try again. Its EZ Connect, Builder Series, Amana and ES models use an automatic overload switch instead: turn the disposal off (unplug it if it runs on a push button air switch) and let it cool for up to 20 minutes. If the motor still does nothing, InSinkErator's next step is the service panel, to look for a tripped breaker or a blown fuse.
InSinkErator describes the overload protector as a device that shuts the disposal off if it is jammed, if it is run for a very long time, or if there is another issue. A button that trips again after the jam is cleared, or a unit that stays silent with the breaker and the switch confirmed, is past the owner checks. That is where a visit makes sense: the wall switch, the electrical connection under the sink and the motor get tested before anyone talks about a new unit.
InSinkErator gives a quick test. Turn the disposal on and watch the water. If you see a whirlpool, you may have a clogged drain line. If there is no whirlpool and the disposal is running, it points to a possible jam. If the disposal is not running at all, go back to the steps above. For a clog, InSinkErator suggests a plunger with about four inches of water in the sink, and a stopper in the other opening of a double sink.
InSinkErator says an odor is usually a sign of food buildup, and that over time food waste can also accumulate under the sink baffle. Its cleaning steps: turn the disposal off, take the baffle out and clean its underside with a scouring pad, put it back, then run the disposal with a medium stream of cold water and drop in ice cubes mixed with lemon or lime wedges.
When a dishwasher drains through the disposal, the connection matters. InSinkErator lists a removable dishwasher inlet plug on its EZ Connect disposals, so when a dishwasher stops draining right after a new disposal goes in, that inlet is the first thing we look at. If the dishwasher itself is the problem, see dishwasher repair and our notes on a dishwasher that will not drain.
A jam, a tripped overload, a loose sink mount or a worn gasket at a connection are usually repairs. A failed motor or a body that leaks from inside usually means a new unit, and we handle the installation as well. If the disposal may still be under the manufacturer's warranty, start with the manufacturer: InSinkErator says all its models carry an in-home limited warranty, and that the serial number can help determine the manufacturing date.
InSinkErator says never to put fats, oils or grease into a disposal or down any drain, and to avoid harsh cleaning products and other non-food products. It also says its Standard Series models can grind any food apart from stringy and fibrous materials such as banana peel, celery and rhubarb.
InSinkErator says neither is harmful to a disposal, but both can create a clog or a slow drain if too much goes in at once or the plumbing is restricted. Its advice is to feed them in gradually with a strong flow of cold water.
InSinkErator says to run a moderate flow of cold water while grinding and for a few seconds after, and to avoid hot water when grinding food waste. It says draining hot water into the disposal between grinding periods is OK.
Often not. InSinkErator's own steps on most of its models are the hex wrench under the unit and the red reset button, or a cool-down period on models with an automatic overload switch. If that gets it running, you have saved yourself a visit, and we would rather tell you that.
Tell us the appliance and what it is doing. The price is agreed before any work starts, and we are open Sunday.